This post details how I got running water in my campervan conversion…
I did separate posts on the shower and hot water and also mounting the shurflo water pump so this post will cover the rest of the water related stuff:
- fresh water tank and filler inlet
- sink and drain
- grey waste tank
- water pump and accumulator (shown in image below)
[expand title=”Show list of materials”] This work was completed over quite a few weeks so apologies for the widely varied supplier list but hopefully it helps people who are trying to find out what all the little bits are [table id=7 /][/expand]
The water tank
The fresh tank was the first thing I put in the van and everything else was build around it, in a make it up as I go along kind of fashion. I used a common Fiamma 70 Litre fresh water tank (for on-board use) from… you guessed it, Amazon (the cheapest I found online was £58 here but most big caravan shops stock them – Magnum and O’leary).
The water system started with a 70L Fiamma fresh tank. I decided to mount this in (probably) an unconventional way, standing on end.
The tank provides several points for the 20mm water outlet. I decided to go for a third of the way up. I could have done it right at the bottom but I got a little worried that the full tank would siphon off in the case of a leak.
I pulled away some of the cladding and added some strengthening lengths of wood to fix the 4 mounting bolts to.
This whole tank will be concealed under the sink/hob unit and the outlet elbow will go straight to the water pump via 12mm semi-rigid hose
The tank will be filled using the filler cap on the back of the kitchen unit and easily accessed via the side door. The hose is 40mm food grade ‘filler hose’ which fits the filler cap neck nicely but needs a good tie wrap or two for a good fit on the water tank inlet.
This is stood looking into the van with the side door open to expose the water filler. I prefer to have this inside the van instead of mounted on the outside of the van body
The sink and drain
The sink/hob unit is from a donor caravan. Matt built a custom frame for it to sit on while I did the cupboard doors. I covered this in the making the kitchen cupboards post.
The hole was too small for the sink drain I had so I opened it up a bit with a cloth wrapped hacksaw blade.
Fits nice and flush. I even remembered to put a bead of silicone round the under side of the lip to ensure not leaks
I connected the red and blue 12mm semi rigid hose to the taps at this point. The tap is a normal domestic mixer tap which meant the hoses just needed a couple of jubilee clips to get a good seal.
I restricted the flow for hot water to minimum but its still more than enough!
The drain comes straight down from the sink and down through the floor
Straight through the floor where it will then combine with the shower waste via a Y-connector and through a waste trap before entering the grey waste tank
I sealed all around the pipe with sikaflex 512 and also made a mess
Grey waste tank
This tank will be used to collect drain water from the sink and shower. It’s not really essential but will be useful when parked up in cities or anywhere I’d like to remain a little inconspicuous. The tank will have to be custom made and will have an inlet (to fit 28.5mm waste pipe) and outlet consisting of a tap mounted directly on the underside of the tank for emptying. Most of the time though, I’ll probably just keep the drain tap open so the water runs through onto the floor and just close it when It is needed.
I decided 20L would be more than enough capacity to collect drain water since I’ll only be using small amounts of water at a time. I contacted Barratt tanks and emailed him over a sketch with my dimensions and rough location for inlet and outlet. He was the cheapest and most helpful person I found (I found him after a recommendation on the SMBCC forum)
Here is a sketch of my tank. I sent this to Shaun at Barratt tanks.
grey waste tank and connections
Y-connector goes straight into the trap and then into the tank via waste pipe
I’ll be using a 30psi Shurflo trail king 7. It seems like a great bit of kit – solid, heavy and sounds like it really knows what it’s doing. I did have some trouble with the noise at first but I solved it by hanging the pump rather than fixing it which I explain here – mounting the shurflo water pump. I fed the pump into an accumulator (Fiamma A20 from O’leary motorhomes) after some unsatisfactory bench (pulsating) tests with no accumulator. The difference is night and day and for £20 its an obvious choice to get the water running nicely.
The pump is central to the proper functioning of the water system so I made sure It was a decent one. It is designed to be serviceable and spare parts readily available
Since these pumps rely on pressure in the system to automatically turn off, they have a tendency to oscillate when the tap is not fully open. A ‘buffer’ is needed to dampen the system and to reduce and oscillatory behaviour – they call it an accumulator. In my opinion, these pumps should always be used with an accumulator and should also lengthen the life of the pumps micro-switch and diaphragm.
I decided to name this the ‘utility cupboard’. In here is the water heater, water accumulator, water pump, 12V terminals and fridge.
Hopefully this give you an idea of how you get install a running water system into your campervan conversion. Please leave any questions or comments below…